13 Things About Fiat Panda Key Fob Replacement You May Never Have Known

Reasons Your Fiat key code 500 Key Fob Won’t Work

A key fob from Fiat 500 makes it simple to open doors and start your vehicle. However, there are numerous reasons why the fob won’t be working. These include a dead battery damage to the receiver module, water issues, and interference.

This listing is for an NEW replacement key fiat 500 Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths for your vehicle). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob that isn’t working. Modern key fobs operate with a restricted operating range, and should be within only a few feet from the car to operate. If you are far from your vehicle and you press the keyfob button it will not respond and display the message «Key Fob Not Detected».

If this happens, replace the battery of your coin cell (Part number CR2032) with a fresh one from a reputable brand like Panasonic, Duracell, or Energizer. You can find them in the local hardware store or on the internet.

After you’ve replaced the coin cell battery, you can test it by standing near your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switch.

If your key fob still does not work after replacing the battery, it may be water damage which prevents it from communicating with the module inside your vehicle. Water damage can happen in a variety of ways, such as an easy splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If that doesn’t work your fob will probably need to be reprogrammed by an experienced auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals that keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually end up dying. It’s not good to get the fob wet, but don’t give it up if you accidentally drop it in water, or fail to remove it from your pants pocket.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Next test the fob to test if it works. If the key doesn’t work, it might need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key you have is older and is not programmed for your vehicle it is necessary to replace it completely. This is a straightforward process that can be completed by a professional locksmith for automotive use. The locksmith will need the key cut to match the car’s ignition. They’ll also have to reprogram the fob for the system of your car. This is a fast and cost-effective process that is usually completed the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop working is that it’s simply out of range. The remote usually has 30 feet of range or less and if it’s far from your vehicle, it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If you’ve replaced the coin battery (commonly called»button» or «button» or «watch») and your fob still won’t work, it could have an internal circuit board problem. Reprogramming the fob usually resolves the issue. You can find the instructions on how to do this for the majority of automobiles by searching YouTube or reading the owner’s manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension it can prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob might be out of sync with your vehicle because due to hardware or software issues. This could cause a significant issue, but you are able to usually resolve this issue by visiting an auto locksmith to reprogram your fob for you. In some cases, the software may also require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This could occur if the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob might not work include a poor connection to the buttons or the internal chip or water damage.

If the key fob stopped working one day suddenly or after trying everything you can do at home to fix it e.g. You might have a damaged 500 receiver module in the event that you’ve tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500’s internal system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer of your car. This can help get your key fob to work again. If the issue persists, you should seek the advice of an expert technician. They can diagnose the exact cause of your problems.