9 Lessons Your Parents Teach You About Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won’t Work

A fiat 500 replacement key near me 500 key fob makes it easy to open doors and start your vehicle. There are a myriad of reasons the fob could stop working. It could be due to a dead battery, damage to the receiver module, water issues, or interference.

This listing is for an NEW replacement fiat panda Key Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn’t function is the battery is dead. Key fobs of today have only a limited range of operation and must be within a few inches of the vehicle in order to function. If you’re far from your vehicle and press the keyfob button, it won’t respond and display the message «Key Fob Not Detected».

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a new one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you’re standing close to your Fiat 500. The parking lights should light up and the key fob should operate the lock and unlock switches.

If the fob’s key doesn’t function after replacing the battery, it might have water damage that prevents it from communicating with the receiver module inside your vehicle. Water damage can occur in many ways, such as simply splashing or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture back out. If this doesn’t work your fob will probably require reprogramming by a professional auto locksmith or by the dealer.

Water Damage

While the fob comes with rubber seals to keep water from the chip’s electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually fail. It’s not a good thing to let the fob get wet but don’t give up even if you accidentally drop the fob in water or fail to take it out of your pants pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl or a similar product and then dry it thoroughly before replacing the battery. Then, test the fob to see if it works. If the key does not function, it may need to be changed. This is usually handled by a dealer or professional auto locksmith.

If the key is older and was not programmed to your car, it will likely need to be replaced completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith will need to cut the key to match the ignition on your vehicle. The locksmith will also need to reprogram your fob into the car’s system. This is a simple and affordable process which can be completed the same day.

Receiver Module Issues

Your 500 key fob might not function because it’s out of range. The remote has a range of 30 feet, which means should you be too far away from your vehicle it won’t respond to your commands. It’s easy to solve this problem by moving the remote closer to your car until it responds.

If you’ve replaced your coin battery (commonly known as»button» or «button» or «watch») and your fob doesn’t function It could be because of an internal circuit board issue. In most cases, reprogramming the fob will solve the problem. You can find the procedure for most vehicles on YouTube or in the owner’s guide.

It could be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension, it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare cases the fob can become out of the vehicle’s sync because of hardware or software problems. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases, they may need to reinstall the software in your body control module as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This could occur if the key fob is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fiat fob might not work include a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you’ve tried everything at home to resolve it (e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a defective receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

There’s a quick and easy way to reset the 500’s on-board system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will erase any remaining electrical charge, and then restart the computer in your car. This will help you get your key fob to work again. If the problem persists you should consult an expert technician. They can determine the root of your problem.