How To Tell If You're Prepared To Go After Peugeot Keys

Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths who have the appropriate equipment and technical know-how. They can create and program keys quicker and more efficiently than a dealership.

A dead coin battery is most likely to be the cause if your key fob stops locking or unlocking the doors. There are many other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking or unlocking and cannot start the engine. In this instance you’ll need to employ the alternate method of starting described in your vehicle owner’s manual.

Another reason the 208 won’t start is because the spark plugs have been worn down. The spark plugs are responsible for sparking the fuel that ignites the engine. However they have a short time of life. They’ll eventually degrade if they’re not used enough.

There is a simple solution for this issue. The best option is to test the voltage of your car battery with a multimeter. If the voltage is lower than 11,5 volts, it’s the time to replace it. If the battery has corroded, it is important to clean its contacts. This can be done by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any corroded parts of the battery. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 won’t start and the battery isn’t flat then you should check whether the spark plugs are working. It could be that they are overly dirty, which causes them not to spark. The spark plugs can be cleaned in a workshop.

peugeot 3008 key fob programming cars use transponder keys that works with the car’s ignition system. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

This is a typical issue that can be caused by water damage. This is most common in colder climates where the vehicle could have been exposed to rain or snow. If this is the case, you should contact a reputable auto locksmith who has all of the tools and equipment needed to modify the new key. They also have the latest technology and equipment needed to make the Peugeot 208 smart key. The process shouldn’t take more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the transponder chips by introducing a new type that uses electronic components mounted on a circuitboard. The new system is excellent when it’s new, however the circuit boards deteriorate over time and cease to function properly.

This could prevent the immobiliser from activating so your vehicle won’t start. Contact a Peugeot specialist or a locksmith, if this is the case.

Another issue that is common is when the battery of the key fob begins to fail, which causes the blade of the key to stop being able to feed into the lock. A locksmith for cars can replace the battery and cut a new blade for you, this is typically a quick fix.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the floor, getting exposed to a sudden downpour or accidently washing it, it could be due to a faulty receiver module. The receiver is responsible for transmitting radio frequency signals to the on-board computer which controls the centralized locking system inside your Peugeot vehicle.

The rubber seals on the key fob block water from getting to the electronic chip. However, prolonged exposure to water can be able to penetrate these seals and cause damage to the chip. Submerging the key fob in the ocean at the beach or throwing it into the pool could be especially damaging because of the high salt content.

The module will have to be replaced if your peugeot key fob replacement spare key is no longer working. This is only performed by a professional auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the right coding for the start of the engine. This is why you must go with a knowledgeable Peugeot locksmith for the job of programming and creating the replacement.

Computers with faulty on-board computers

The computer on the board of your Peugeot is responsible for a variety of the systems within your car, ranging from power windows to the airbags. When something goes wrong in these systems, they will usually display a code indicating the issue. The code is stored in the system until the problem is fixed. In most cases, this will require the on-board computer being replaced.

The most typical reason for the warning light for the airbag to illuminate is corrosion or loose connections within the sensor. This can be caused by wear and tear, aging or exposure to moisture and salt. It is crucial to get this issue addressed as quickly as possible, as an airbag that is not functioning properly could be dangerous in the event an accident.

If your Peugeot is showing a card that is not being detected error, then the battery in the key fob might be dead or weak. This will stop the key fob from sending a signal to deactivate the vehicle’s immobilizer. Try this by pressing the unlock button on the fob’s key and then trying to start your vehicle. If it doesn’t work then the battery in the key fob needs to be replaced.